Hatsan Flashpup Airgun PCP pressure regulator-Altaros

Description

EBAYERS!!! Please Note - We have checked that this item is not prohibited under your Firearms, Ammunition, Replicas and Military importation policy. This is a Pressure Regulator!
Airgun pressure regulator for Hatsan Flash,Hatsan Flashpup, NEW BT65 made in 2018 and later
Regulator can be used in new
Hatsan Flash version which does not have magnetic aritube
Working pressure is
4350 PSI / 300 bar.
Regulator has scale
1450 – 2175 PSI  /100-150 bar.
For higher powers can be regulator set
up to 2465 PSI / 170 bar
.
Regulator weight 67 gram
Here at Altaros Regulators, we feel that what makes our regulators better for the end user than our competitors. Firstly is that our regulators place
minimum demands on the skills and equipment
needed for installation.
Our regulators have a very precise output pressure, often achieves consistency between
1-3bar (14.5 - 43.5 psi),
which has a very positive impact on the projectile’s consistency of speed, which varies by
only +/- 1-1.5 mps (+/- 3-5 fps
).
Our regulator’s main feature is that they require no permanent modifications on your airgun, so you can revert your mechanism and airtube to its original state at any time during or after installation! Unlike our competitor’s regulators,
there is never a need to drill any holes at all.
Installation is simple!
In short, all you need to do is; first drain all pressure from airtube, unscrew the valve body from the air tube.
Spray o-rings with silicone oil, then push regulator inside airtube (with circular movement like when you screwing valve, this movement will prevent damaging outer o-ring on regulator) in such depth so you can see 1/2 thread inside airtube.
Remove original o-ring from valve cap and screw valve back in airtube.
By screwing plug we get regulator into correct position. Do not tight airtube and valve fully. Leave gap 0.1-0.2 mm between them, by doing this and removing o-ring from valve you creating venting hole (with this is no drilling to airtube needed).
To keep installation as simple and clear as possible,
we have created a series videos to guide
you step-by-step through the installation process, even if you’re not the technical type! These videos are on
YouTube tagged as Altaros Regulator
(channel Altaros Airgun Regulator).
To find instructions, results and other info you can check Altaros.cz
We make brand/model specific regulators for most air rifles!
Check out our web page!
As always, if there is ever a question, you can always send an email to us, to which you will promptly receive an answer as quickly as we can.
With regulators arrive pack with
spare
o-rings.
Another thing which makes us different from competitors is that we do not want earn money on spare o-rings and sell them for ridiculous amount of money.
We have list with o-rings sizes online, so you can buy them in your country for minimal price,
or from us for 3 euro
+ shipping.
Here is list of o-rings used in
Hatsan Flash,Hatsan Flashpup, NEW BT65 made in 2018
:
n
br = hardeness
Outer o-ring (which lean to airtube) on regulator body is 21x2,5 nbr 70
Inner o-ring (which lean to valve) on regulator body is 22x1,5 nbr 90
O-ring used on plastic screw (screw for setting pressure) 4x1 nbr 90
O-ring on dural (silver) cylinder 7x1,5 nbr 70
O-ring on dural (silver) cylinder
9,25x1,78  nbr 90
O- rings on brass piston 2 pieces 7x1,5 nbr 70
O-rings on piston behind sping disc 3 pieces 3x1,5 nbr 90
We send our goods worldwide
with FREE SHIPPING!
Acceptance of delivery:
Please check immediately integrity of the envelope and content. If the shipment did not contain the goods, or is visible damaged, then immediately claim a complaint with the carrier or not accept the consignment.
Thank you for choosing an Official Altaros Brand Regulator.
Whole ALTAROS team wishing you  Happy and Accurate Shooting!!